As part of the big lab I am doing I want to do some work with Frame Relay. Nothing too exciting at the moment, but I do want to touch on it.
So with IOU I want a Frame Relay connecting to four other routers in a hub and spoke topology. Pretty simple right?
Well using this netmap:
5:0/0 1:0/0
5:0/1 2:0/0
5:0/2 3:0/0
5:0/3 4:0/0
I get what I want:
Frame Relay basic configuration
I can set up my FR switch as follows:
hostname FR1 ! boot-start-marker boot-end-marker no aaa new-model clock timezone CET 1 0 mmi polling-interval 60 no mmi auto-configure no mmi pvc mmi snmp-timeout 180 ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ip cef no ipv6 traffic interface-statistics no ipv6 cef frame-relay switching multilink bundle-name authenticated crypto pki token default removal timeout 0 redundancy ! interface Serial0/0 description Connected to R1 no ip address encapsulation frame-relay no keepalive serial restart-delay 0 no frame-relay inverse-arp frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 102 interface Serial0/1 201 frame-relay route 103 interface Serial0/1 301 frame-relay route 104 interface Serial0/1 401 ! interface Serial0/1 description Connected to R2 no ip address encapsulation frame-relay shutdown no keepalive serial restart-delay 0 frame-relay intf-type dce frame-relay route 201 interface Serial0/0 102 ! interface Serial0/2 description Connected to R3 no ip address encapsulation frame-relay no keepalive serial restart-delay 0 frame-relay intf-type dce frame-relay route 301 interface Serial0/0 103 ! interface Serial0/3 description Connected to R4 no ip address encapsulation frame-relay no keepalive serial restart-delay 0 no frame-relay inverse-arp frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 401 interface Serial0/0 104 !
Ok, so nothing too complicated here.
Looking at R1 and R4 (truncated):
hostname R1 ! interface Serial0/0 no ip address encapsulation frame-relay serial restart-delay 0 frame-relay lmi-type ansi ! interface Serial0/0.14 point-to-point ip address 10.1.14.1 255.255.255.0 frame-relay interface-dlci 104 ! hostname R4 ! interface Serial0/0 no ip address encapsulation frame-relay serial restart-delay 0 frame-relay lmi-type ansi ! interface Serial0/0.41 point-to-point ip address 10.1.14.4 255.255.255.0 frame-relay interface-dlci 401 !
I should be able to ping R4 from R1 and R1 from R4, but “sh ip int bri” shows that the sub-interfaces are down/down and the physical interface is up/down. If I add “no keepalive” to the physical interfaces they come up, but I still can’t ping across them:
So the config looks ok, the interfaces are up, and we know from part two of the big lab series that serial interfaces do work on IOU, so what’s the problem? Well it looks to be an issue in IOU:
DCE and DTE
Look at the result of the “sh int serial 0/3”, it clearly shows that its set to Frame Relay DCE, but the result of the “sh controllers serial 0/3” shows a very different story:
It’s showing a cable type of DTE.
Having a look at the netmap tutorial on Route Reflector page it shows a Frame Relay switch sitting in the middle of a bunch of routers and the netmap has 107 at the end of the connections, 107 being the Link-Layer header type for Frame Relay. So if I change my netmap to:
5:0/0 1:0/0 107
5:0/1 2:0/0 107
5:0/2 3:0/0 107
5:0/3 4:0/0 107
I get this:
Clearly, this is not what I am looking for!
Means I have to rethink how my big lab topology will pan-out. I am guessing it’ll be without Frame-Relay for the time being! Even Andrea over at Route Reflector states that serial interfaces appear as DTE in the FAQs.
If anyone knows how to get around this, I’d love to hear from you. I have tried a number of different images but so far nothing works.
I am going to continue playing around, so hopefully will be able to pull something out of the hat, unless there is someone out there that can point me in the right direction…
*Update* GNS3 works fine with the same configs.